SE98A_4
?NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04  25 November 2009
6 of 43
NXP Semiconductors
SE98A
DDR memory module temp sensor, 1.7 V to 3.6 V
7.3  EVENT
 output condition
The EVENT
 output indicates conditions such as the temperature crossing a predefined
boundary. The EVENT
 modes are very configurable and selected using the configuration
register (CONFIG). The interrupt mode or comparator mode is selected using CONFIG[0],
using either TCRIT/UPPER/LOWER or TCRIT only temperature bands (CONFIG[2]) as
modified by hysteresis (CONFIG[10:9]). The UPPER/LOWER (CONFIG[6]) and TCRIT
(CONFIG[7]) bands can be locked. Figure 6
 shows an example of the measured
temperature versus time, with the corresponding behavior of the EVENT
 output in each of
these modes.
Upon device power-up, the default condition for the EVENT
 output is high-impedance to
prevent spurious or unwanted alarms, but can be later enabled (CONFIG[3]). EVENT
 
output polarity can be set to active HIGH or active LOW (CONFIG[1]). EVENT
 status can
be read (CONFIG[4]) and cleared (CONFIG[5]).
" Advisory notification:
  NXP device: After power-up, bit 3 (1) and bit 2 or bit 0 (leave as 0 or 1) can be set 
at the same time (e.g., in same byte) but once bit 3 is set (1) then changing bit 2 or
bit 0 has no effect on the device operation.
  Competitor device: Does not require that bit 3 be cleared (e.g., set back to (0)) 
before changing bit 2 or bit 0.
  Work-around: In order to change bit 2 or bit 0 once bit 3 (1) is set, bit 3 (0) must be 
cleared in one byte and then change bit 2 or bit 0 and reset bit 3 (1) in the next
byte.
  SE98B will allow bit 2 or bit 0 to be changed even if bit 3 is set.
If the device enters Shutdown mode (CONFIG[8]) with asserted EVENT
 output, the output
remains asserted during shutdown.
7.3.1   EVENT
 pin output voltage levels and resistor sizing
The EVENT
 open-drain output is typically pulled up to a voltage level from 0.9 V to 3.6 V
with an external pull-up resistor, but there is no real lower limit on the pull-up voltage for
the EVENT
 pin since it is simply an open-drain output. It could be pulled up to 0.1 V and
would not affect the output. From the system perspective, there will be a practical limit.
That limit will be the voltage necessary for the device monitoring the interrupt pin to detect
a HIGH on its input. A possible practical limit for a CMOS input would be 0.4 V. Another
thing to consider is the value of the pull-up resistor. When a low supply voltage is applied
to the drain (through the pull-up resistor) it is important to use a higher value pull-up
resistor, to allow a larger maximum signal swing on the EVENT
 pin.
相关PDF资料
SG6901ASZ IC PFC CTLR AVERAGE CURR 20SOIC
SG6932SZ IC PFC CONTROLLER CCM 16SOP
SG6961SY IC PFC CTRLR AVERAGE CURR 8SOIC
SI3500-A-GM IC POE SWITCH PWR OVER LAN 20QFN
SI786LSG-E3 IC REG QD BUCK/LINEAR 28SSOP
SIC417CD-T1-E3 IC REG DL BCK/LINEAR SYNC 32MLPQ
SP619EK-L/TR IC HIGH CURRENT SW SOT23-6
TC573302ECTTR IC REG CTRLR SGL 3.3V SOT23A-5
相关代理商/技术参数
SE98PW 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:SO-DIMM SMBus/I2C-bus temperature sensor
SE98PW,118 功能描述:板上安装温度传感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SE98PW-T 功能描述:板上安装温度传感器 I2C LOCAL +/- 2OC TS DIMM RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SE98TK 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:DDR memory module temp sensor, 3.3 V
SE98TK,118 功能描述:板上安装温度传感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SE98TK-T 功能描述:板上安装温度传感器 I2C LOCAL +/- 2OC TS DIMM RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SE9E1210A1.5-4R 制造商:JOSLYN 功能描述: 制造商:JOSLYN SUNBANK COMPANY LL 功能描述:
SE9ESA847R100 制造商:Lanner Electronics Inc 功能描述:WALL MOUNT-2 V1.0